CHIRP

the same problem when I try chirp on a windows PC. not only a Mac problem

Its on the right COM port. I can use the software from abbree but somehow Chirp isn't able to access it

tried with chirp legacy. doesn't work .

From the debug.log file it would seem that your programming cable has a Prolific type USB-to-Serial chip. That is most likely the problem.

For macOS the solution is to get a programming cable that uses the FTDI type chip. An example would be the PC03 sold by Baofeng Tech (the radio dealer in the USA) but this type of cable can be acquired from several sources.

https://baofengtech.com/product/pc-03-programming-cable/

For Windows the programming cable mentioned above would work but you can also manually download, install and select the older Prolific v3.2.0.0 driver as a workaround. A link to the driver and instructions for selecting it can be found on the Miklor Radio Information website. Keep the driver handy because Windows will at some point in the future upgrade the driver and you will have to (sometimes re-install it and) select it again.

https://www.miklor.com/COM/UV_Drivers.php

Jim KC9HI

i have tried with AR-518 from abbree ( the AR-63 doesn't have a connexion)
also tried with wouxoun UV8D ( no connexion)

I'm really a loser in computer....

frederic monier wrote in #note-8:

the log with my pc and the fdti dongle
thanks for the help

The debug.log file shows that you are selecting the wrong radio.

Jim KC9HI

helli Jim,
i have tried with abbree AR518 and also with woxun UV8D.
witch radio do I have to select please?
thanks for your help

@Jim Tuit, if you want to try via team viewer , I'm your man...

jim KC9KI and not tuit.

frederic monier wrote in #note-13:

retry from my Mac
log

I would ap

frederic monier wrote in #note-12:

retry from my pc
new log

There is no communications with the radio.

The log from the PC seems to indicate that many different ports are being tried. There is only 1 correct port to select. If you click "Help Me..." in the drop-down list for selecting the "Port", CHIRP-next will assist you with selecting the correct port.

Another common cause for this is not getting the 2-pin plug is fully inserted into the socket of the radio. Double check this. Sometimes the rubber cover for the speaker/mic socket can get in the way and interfere with getting the plug fully inserted.

Jim KC9HI

Jim Unroe wrote in #note-16:

I would ap
what do you mean by "i would ap" ?

frederic monier wrote in #note-18:

Jim Unroe wrote in #note-16:

I would ap
what do you mean by "i would ap" ?

This was in error. I aborted my reply to your mac post to reply to your PC post and somehow it was not abandoned as it should have been but instead prepended to my reply.

Jim

hi
can you confirm I have to use the wouxoun UV8D on chirp?
cable is well connected because I can use the RPS from ABBREE.
thanks a lot for your help

hello , can someone can confirm I have to use the woxun UV8D for my radio ?

do you know if a version of chirp will work with this new firmware ?

hello, have you news about the compatibility of the new firmware with chirp ?

just to Know if it will be done ? thanks for your work

hello, no news ?

frederic monier wrote in #note-25:

Thanks for the software. It works
Hope it will be on chirp one day
It’s the same firmware

Frederic,
Where can I download the software that has been deleted from here? I have the same radio and issue that John was having. Thanks in advance.

Ron

hello, I don't have the solution. I have the problem . software was given by dan. but I d'ont have it anymore. I hope that chirp will work with this radio a day or an other. good luck

hello, still the same problem.

still no news ?

no news ?