Project

General

Profile

Actions

Bug #8223

closed

Error reading data from radio: not the amount of data we want. UV-82 III

Added by Melvin Davis over 4 years ago. Updated about 4 years ago.

Status:
Closed
Priority:
Normal
Assignee:
-
Category:
-
Target version:
Start date:
08/30/2020
Due date:
% Done:

0%

Estimated time:
Chirp Version:
daily
Model affected:
Radioddity UV-82X3
Platform:
Windows
Debug Log:
I read the instructions above:

Description

Just received this radio and tried to do a download and got this error.
Cable is a Baofeng branded cable using the CH340 driver. I tried on a UV-82 and a UV-5r and it read the radios fine.
I also uninstalled chirp and tried version 20200204 with no luck.
Not sure if its a bad radio or software issue.


Files

Baofeng_UV-82HP_20200830.img (6.5 KB) Baofeng_UV-82HP_20200830.img Melvin Davis, 08/30/2020 06:19 PM
Baofeng_UV-82_20200830.img (6.5 KB) Baofeng_UV-82_20200830.img Melvin Davis, 08/30/2020 06:19 PM

Updated by Melvin Davis over 4 years ago

Was able to get to download as a UV-82 and UV-82HP.
Firmware is HN5RV01

Actions #2

Updated by Jonpas J over 4 years ago

Can confirm on 2 new radios. Cannot retrieve image file so cannot test upload.

Actions #3

Updated by Jim Unroe over 4 years ago

  • Status changed from New to Feedback

Baofeng must have 2 different versions of the UV-82III. The one listed in the UI is for the "waterproof" case style models (similar to BF-A58, GT-3WP, Retevis RT6, etc.). The radios you have are the tri-band UV-82 version which would use the Vendor: Radioddity | Model: UV-82X3 selections.

Jim KC9HI

Actions #4

Updated by Jonpas J over 4 years ago

Correct, they are the newer tri-band versions. I just re-tried with UV-82HP selection in the UI, that one can be downloaded and also uploaded successfully!

The remaining problem is no settings can be configured in the UI after downloading the image from the radio.

Actions #5

Updated by Jonpas J over 4 years ago

Scratch last, using "UV-82" selection allows the settings to be changed as well. Thanks for the pointer!

Supported devices list should probably get a note regarding the use of UV-82 selection for USV-82 III (tri-band) radios.

Actions #6

Updated by Melvin Davis over 4 years ago

I should have updated this earlier.
I'm using the UV82x3 and it works fine.

The UV-82 selection will work but won't allow 220mhz frequencies to be input into a channel. It throws an error.

Actions #7

Updated by Jonpas J over 4 years ago

That makes sense. I don't see UV82x3 in my UI on 20200909 version, but I might be a bit behind.

Actions #8

Updated by Melvin Davis over 4 years ago

I'm using CHIRP daily-20200827.
Its listed as a Radioddity radio.

Actions #9

Updated by Jim Unroe over 4 years ago

Jonpas J wrote:

That makes sense. I don't see UV82x3 in my UI on 20200909 version, but I might be a bit behind.

It isn't listed under Baofeng. You should use...

Vendor: Radioddity
Model: UV-82X3

Jim KC9HI

Actions #10

Updated by Jonpas J over 4 years ago

Ah, that makes a lot of sense! Thank you both!

Actions #11

Updated by Bernhard Hailer about 4 years ago

  • Status changed from Feedback to Closed
  • Model affected changed from UV-82 III to Radioddity UV-82X3

Resolved.

Actions

Also available in: Atom PDF